Welding Shop

Name of the Equipments/Machine:
»1. TIG Welding Machine
»2. MIG Welding Machine
»3. Electric are welding Equipment
»4. Gas Welding Equipment

Scope of the Experiments:
»1. Gas Welding practice by students on mild steel flat
»2. Lap joint by MMA welding
»3. Lap joint by gas welding

Heat & Mass Transfer Lab

Name of the Equipments/Machine:
»1. Apparatus of Heat Transfer of pin - fin.
»2. Apparatus of a conductivity of the Insulating powder.
»3. Apparatus of composite wall.
»4. Apparatus of natural convection.
»5. Apparatus of emissivity.
»6. Apparatus of Stefan Baltzman.
»7. Apparatus of thermal conductivity of a metallic rod.
»8. Apparatus of Parallel and Counter Flow Hear Exchanger.

Scope of the Experiments:
»1. To determine Thermal conductivity of Insulating Powders.
»2. To determine Thermal Conductivity of a Good Conductor of Heat (Metal Rod).
»3. To Measure the thermal Conductivity of Liquid.
»4. To determine the transfer Rate & Temperature Distribution for a Pin Fin.
»5. To Measure the Emissivity of the Test plate Surface.
»6. To Determine Stefan Boltzman Constant of Radiation Heat Transfer.
»7. To Determine the Surface Heat Transfer Coefficient For Heated Vertical Cylinder in Natural Convection.
»8. Determination of Heat Transfer Coefficient in Drop Wise & Film Wise condensation.
»9. To Study and Compare LMTD and Effectiveness in Parallel and Counter flow Heat Exchangers.
»10. To Find the Heat Transfer Coefficient in Forced Convection in a tube.

Thermal Lab

»1. I.C. Engine Lab.
»2. Automobile Engineering Lab.
»3. Heat Mass Transfer Lab.
»4. Refrigeration & Air Conditioning Lab.

IC Engine Lab

Name of the Equipments/Machine:
»1. Single cylinder 4 - stroke diesel engine test Rig. (Electric dynamometer).
»2. Single cylinder 4 - stroke diesel engine test Rig. (Rope dynamometer).
»3. Single cylinder two stroke petrol engine.
»4. Multi cylinder four stroke petrol engine (Morse test Rig.).
»5. Various compressor computerized single cylinder diesel engine.
»6. Double stage air compressor.
Scope of the Experiments: (Second Year III Sem).
»1. Comparative study of four stroke diesel and petrol engines.
»2. Comparative study of two stroke petrol and diesel engines.
»3. Studies of fuel supply systems of diesel and petrol engines.
»4. Study of cooling lubrication and ignition system in diesel and petrol engines.
»5. To study various types of Boilers and to study Boiler mounting and accessories.
»6. To study Multi Stage Air Compressors.
»7. To find the BHP, Thermal efficiency of four stroke diesel engine.
»8. Study of Brakes, Clutches, and Transmission System.
Second Year (IV Sem):
»1. Disassembling and assembling of multi-cylinder petrol and diesel engines and study of their parts.
»2. To disassemble and assemble a 2-stroke petrol engine.
»3. To disassemble and assemble a 4-stroke motor cycle engine and study of various engine parts.
»4. Load test on a single cylinder 4-stroke diesel engine using a rope brake dynamometer and calculate volumetric and thermal efficiency and draw a heat balance sheet.
»5. Study of carburetors and MPFI system and disassembling and assembling of their parts.
»6. To calculate valve timing of a multi-cylinder petrol engine and valve tappets adjustment.

Foundry Shop

Name of the Equipments/Machine:
»1. Tilting Furnace.
»2. Pit Furnace.
»3. All type of foundry tools (Like pin rammer, strike of bar, claw hammer, hand rammer, runner, riser, molding box etc.)
»4. Good number of Wooden Patterns
Scope of the Experiments:
»1. Moulding Sands, constituents and characteristics
»2. Role of gate, runner, riser, core and chaplets.
»3. Cause and remedies of some common casting defects like blow holes, cavities, inclusions.

Fluid Mechanics Lab

Name of the Equipments/Machine:
»1. Bernoullis theorem Apparatus.
»2. Conducting Office Apparatus.
»3. Meta-eccentric height Apparatus.
»4. Notch (V, Rectangular & Trapezoidal) Apparatus.
»5. Pitot Static tube Apparatus.
»6. Pipe friction Apparatus.
»7. Nozzle meter Apparatus.
»8. Orifice meter Apparatus.
»9. Venture meter Apparatus.
»10. Kaplan turbine model.
»11. Pelton turbine model.
Scope of the Experiments:
»1. Determine Metacentric height of a given body.
»2. Determine Cd, Cv & Cc for given orifice.
»3. Determine flow rate of water by V-notch.
»4. Determine velocity of water by pitot tube.
»5. Verify Bernoulli's theorem.
»6. Determine flow rate of air by Venturi meter.
»7. Determine flow rate of air by orifice meter.
»8. Determine head loss of given length of pipe.
»9. Determine flow rate of air by nozzle meter.
»10. Study of Pelton, Kaplan Turbine models.

Dynamics of Machines Lab

Name of the Equipments/Machine:
»1. Co-efficient of friction apparatus.
»2. Motorized Gyroscope apparatus.
»3. Trifler suspension system.
»4. Setup of Governor.
»5. Static and dynamic balancing apparatus.
»6. Gear train & holding torque apparatus.
»7. Journal bearing apparatus.
»8. Models of different types of cam flower, brakes, dynamometer, clutch etc.
Scope of the Experiments: (Second Year)
»1. To study inversion of four bar chain.
»2. Coupling Rod.
»3. Beam Engine.
»4. Steering Mechanism.(a) Study of quick return mechanism. (Crank and Slotted lever mech.) (b) To draw velocity and acceleration diagram for Crank and slotted lever mechanism.
»5. To determine co-efficient of friction.
»6. To determine moment of inertia of the given object using of Trifler suspension.
Third Year
»1. To verify the relation T=loop for gyroscope..
»2. To plot force vs. radius and lift vs. speed curves for governors.
»3. To plot pressure distribution curves on a journal bearing.
»4. To perform static and dynamic balancing on balancing setup.
»5. To determine mass moment of inertia of a flywheel.

Machine Shop

Name of the Equipments/Machine
»1. Centre Lathe Machine.
»2. Capstan Lathe Machine.
»3. Shaper Machine.
»4. Milling Machine.
»5. Radial Drilling Machine.
»6. Power Hacksaw.
»7. Tool Cutter Grinder.
Scope of the Experiments (First Year):
»1. Job on lathe with one step turning and chamfering operations.
»2. Job on shaper for finishing two sides of a job.
»3. Drilling two holes of size 5 and 12 mm diameter on job used/ to be used for shaping .
»4. Grinding a corner of above job on bench grinder.
Second Year (Production Practice):
»1. Study of lathe machine, lathe tools cutting speed, feed and depth of cut.
»2. To perform step turning knurling and chamfering on lathe machine as per drawing.
»3. Taper turning by tailstock offset method as per drawing.
»4. To cut metric thread as per drawing.
»5. To perform square threading, drilling and taper turning by compound rest as per drawing.
»6. To study shaper machine, its mechanism and calculate quick return ratio.
Scope of the Experiments (Third Year):
»1. Study of single point cutting tool geometry & grind the tool as per given tool geometry.
»2. Study the milling machine, milling cutters, indexing heads and indexing methods.
»3. Prepare a gear on milling machine.
»4. Prepare a hexagonal/octagonal nut using indexing head on milling m/c and to cut BSW/METRIC internal threads on lathe.
»5. To cut multi-start square/metric threads.
»6. To cut external metric threads & to meet it with the nut.
»7. To prepare the job by eccentric turning on lathe machine.
»8. To prepare a job on shaper from given MS rod.
»9. To study the various crystal structures and dislocations through models.
»10. To study the Iron Carbide Equilibrium Diagram and sketch the various structures present at room temps.
»11. Study of capstan lathe and its tooling and prepare a tool layout & job as per given drawing.
»12. Study the principle & construction of the Metallurgical Microscope.

Carpentry Shop

Name of the Equipments/Machine
»1. Wood turning Lathe machine.
»2. Chain Mortise Machine.
»3. Zig saw Machine.
»4. All type of carpentry tools (like clamps, mallets, vices, plainer, chisel etc.).
»5. Hand drill machine & Hand zig saw machine.
»6. Wood Working Machine.
Scope of the Experiments:
»1. Timber, difinition, engineering applications, seasoning and preservation.
»2. Prepare a T - Lap joint & bridle joint.

Fitting Shop

Name of the Equipments/Machine
»1. Bench Vice.
»2. Machine Vice.
»3. Bench Drill Machine.
»4. All type of calipers.
»5. Marking Tools.
»6. Measuring Tools.
»7. All types of Files. (Round, half round, Flat, knife edge, triangular file etc.).
Scope of the Experiments:
»1. To prepare a job according to given drawing (Marking, filing, sawing etc.).

Metrology Lab

Name of the Equipments/Machine
»1. Vernier Calipers.                 »2. Vernier Height Gauge.
»3. Gear tooth Vernier caliper.   »4. Micrometer.
»5. Dial Gauge Indicator.           »6. Bevel Protector.
»7. Combination set.                »8. Go & No Go Gauge.
»9. Megnetic V- Block.             »10. Profile projector.
»11. Radius Gauge.                 »12. Surface Plate.
»13. Slip Gauge.                     »14. Sine Bar.
»15. Three Wire unit Gauge.      »16. Thread pitch gauge.
»17. Thickness gauge.             »18. Tool makers microscope.
»19. Plug gauge.
Scope of the Experiments:
»1. To measure a gap with help of slip gauges.
»2. Measurement of angle/taper using a sine bar.
»3. Study and use of a bore gauge.
»4. Measurement of screw thread elements by tool Makers microscope and Inspection of various elements of screw thread by optical projector.
»5. Measurement of chordal thickness of Gear tooth by Gear tooth vernier caliper.
»6. Use of three-wire method to determine the effective diameter of external threads.
»7. To study the capstan lathe, tool holders and attachments and to prepare the given job as per given drawing.
»8. Measurement of flatness and roundness of a given achine/ground/lapped flat and round surface respectively using dial gauge.

Material Testing Lab

1. Material Science Lab
2. Mechanics of Solid Lab
Name of the Equipments/Machine
»1. Inclined Metallographic Microscope.
»2. Metallographic Polishing Machine.
»3. Specimen Leveler.
»4. Rockwell Hardness tester.
»5. Heat Treatment Furnace.
»6. Metallographic Mounting press.
Scope of the Experiments:
»1. Disassembling and assembling of multi-cylinder petrol and diesel engines and study of their parts.
»2. Annealing of Steel - Effect of annealing temperatures and time on hardness.
»3. To prepare metallic samples for metallographic examination and to study the principle and construction of the Metallurgical Microscope.

Mechanics of Solid Lab

Name of the equipments/Machine:
»1. Computerized Universal Testing Machine.
»2. Torsion Testing Machine.
»3. Spring Testing Machine.
»4. Rockwell Hardness tester.
»5. Fatigue Testing Machine.
»6. Izod Impact testing.
Scope of the Experiments:
»1. Tensile Testing, Compression Testing.
»2. Study of Fatigue Testing Machine.
»3. Brinell Hardness Testing.
»4. Spring Testing.
»5. Izod Impact Testing.
»6. Torsion Testing.

Automobile Engineering Lab

Name of the equipments/Machine:
»1. Head grinding tool kit.
»2. Head valve grinding tool kit.
»3. Injector & Fuel pump.
»4. Model of Lubrication system.
»5. Model of Cooling system.
»6. Model of Ignition system.
»7. Model of wenkle engine.
»8. Model of 2 - stroke & 4 - stroke petrol engine.
»9. Model of 2 - stroke & 4 - stroke diesel engine.
»10. Model of steering system & rear wheel.
Scope of the Experiments:
»1. Valve re facing and valve seat grinding and checking for leakage of valves.
»2. Trouble shooting in cooling system of an automotive vehicle.
»3. Trouble shooting in the ignition system, setting of contact breaker points and spark plug gap.
»4. Demonstration of steering system and measurement of steering geometry angles and their impact on vehicle performance.
»5. Trouble shooting in braking system with specific reference to master cylinder, brake shoes, overhauling of system and the adjusting of the system and its testing.
»6. Fault diagnosis in transmission system including clutches, gear box assembly and differential.
»7. Replacing of ring and studying the method of replacing piston after repair.

Vibration Lab

Name of the equipments/Machine:
»1. Universal vibration setup.
»2. Electro-dynamic exciter & vibration meter.
»3. Whirling of shaft.
»4. Vibxpert Vibration Analyzer.
Scope of the Experiments:
»1. To verify relation T=π/(1/g) for a simple pendulum.
»2. To determine radius of gyration of compound pendulum.
»3. To determine the radius of gyration of given bar by using bifilar suspension.
»4. To determine natural frequency of a spring mass system.
»5. Equivalent spring mass system.
»6. To determine natural frequency of free torsional vibrations of single rotor system. (a) Horizontal rotor (b) Vertical rotor
»7. To verify the dunkerley's rule.
»8. To conduct experiment of trifler suspension.
»9. Harmonic excitation of cantilever beam using electro-dynamic shaker and determination of resonant frequencies.

Fluid Machine Lab

Name of the equipments/Machine:
»1. Kaplan Turbine test Rig.
»2. Pelton Wheel Turbine test Rig..
»3. Francis Turbine test Rig.
»4. Centrifugal Pump test Rig.
»5. Hydraulic Ram.
Scope of the Experiments:
»1. Performance characteristics of Pelton wheel turbine.
»2. Performance characteristics of Francis turbine.
»3. Performance characteristics of Kaplan turbine.
»4. Performance characteristics of variable speed centrifugal pump.

Refrigeration & Air Conditioning Lab

Name of the equipments/Machine:
»1. Vapour compression cycle test rig.
»2. Air conditioner test Rig.
»3. Mechanical Heat Pump.
»4. Desert cooler.

Computer Lab

Name of the Machine/Software:
»1. Robotic Arm Trainer.      »2. CNC Turning Centre.
»3. Printer cum Copier.       »4. LCD Projector.
»5. Auto CAD Software.      »6. Solid Works Software.
»7. Think Design Software. »8. Computers (25).
»9. Scanner.                    »10. CAM Software.
»11. FMS Setup.              »12. CAD Sfotware.
Scope of the Experiments:
»1. Program for revising control statements, arrays and functions.
»2. Program using string handling and various functions described in string.h, ctype.h.
»3. Program using structures and sorting algorithm (Insertion, Selection, Quick, Head sort) and functions described in math.h.
»4. Program using file handling and related functions defined in stdio.h, io.h.
»5. Program using pointers, array and pointers, pointers to structures, dynamic memory allocation.
»6. Program using basic I/O and control statements.
»7. Program using class, objects, objects as function parameters.
»8. Program using functions and passing reference to a function, inline functions. Program using Inheritance and virtual base class.
»9. Program using pointers, arrays, dynamic arrays. Program using functions defined in ctype.h and string.h.
»10. Program using constructors, destructors. Program using function and operator overloading.
»11. Creating and managing (add,delete,print,insert) nodes of a Linked list.
»12. Creating and managing (create,pop, push etc.) stacks and queues.

CAD Lab

»1. To prepare part programming for plain turning operation.
»2. To prepare part programming for turning operation in absolute mode.
»3. To prepare part program in inch mode for plain turning operation.
»4. To prepare part program for taper turning operation.
»5. To prepare part program for turning operations using turning cycle.
»6. To prepare part program for threading operation.
»7. To prepare part program for slot milling operation.
»8. To prepare part program for gear cutting operation.
»9. To prepare part program for gear cutting using mill cycle.
»10. To prepare part program for drilling operation.
»11. To prepare part program for multiple drilling operation in Z-axis.
»12. To prepare part program for multiple drilling in X-axis.
»13. To prepare part program for multiple drilling in X and Z axis using drilling cycle.